Add a header to begin generating the table of contents

    Build a Linux Based Raspberry Pi Drone

    Build a Linux Based Raspberry Pi Drone

    Learn how to design, build, fly and even code your own raspberry pi drone from scratch!

    What you’ll learn

    How to use python to script automatic drone missions
    Learn to fly a drone with the open source ArduPilot firmware
    How to design a drone and find the right parts
    How to take raw parts and build a flyable drone
    Compile your own firmware right from the drone

    Build a Linux Based Raspberry Pi Drone

    Requirements

    Windows computer
    Raw parts to build a drone (motors, frame, escs, lipos, raspberry pi/navio etc) Estimated cost: ~$450
    Have basic tools (soldering iron, screw driver, allen wrench, drill would be helpful)

    Description

    Welcome to the ‘Build a Linux Based Raspberry Pi Drone’ course, where we will be covering the gauntlet of drone related subjects. Most drone build courses will only show you how to put together pre-selected parts, without providing the potent ‘why’ behind the choices.

    And they certainly don’t show you how to code your own automatic missions with python.

    This course will cover it all. Whether you want to simply build a flyable drone from scratch, or to learn how to select parts to design your own drone, or even to learn about software that would allow you to script automatic drone missions (for that new ‘taco delivery’ company idea?), we’ll go over it in this course with a unique Linux based Raspberry Pi drone!

    In this course, you will learn:

    Hardware: Basic Drone Components (GPS, motors, ESCs, LiPos etc)

    Design: How to find the basic hardware parts to build your own drone

    Building: Assemble and build your drone from the parts that were chosen from the design process

    Flying: Basic flying and best practices

    Coding: SSH into your Linux drone and configure/code it from the command line

    Some highlights we will learn from the 5 sections:

    Learn of the special units for all your required hardwire (Example:

    What does the C-rating of a LiPo battery actually mean?

    How do mAh and Coulombs relate?

    What’s the difference between a 2300 Kv motor and a 935 Kv motor?)

    Different methods of estimating thrust/current draw of your drone design before you buy the parts

    Soldering ESCs to the power distribution board

    Setting up Telemetry and connecting your drone to Mission Planner (our ground control station)

    Different types of flight modes we can fly our drone with (Example: Loiter- GPS based mode that attempts to lock the drone in a single point in 3D space, Alt-Hold- Barometer based flight mode to hold the drone at a particular altitude)

    SSH-ing into our Linux drone

    Compile our own firmware right from our drone (could even be flying while we are doing this!)

    Download DroneKit and write some python scripts that will make our drone fly autonomous missions (without an RC controller!)

    Will you need to buy drone parts to get value from this course?

    While this course was designed for you to follow along with the drone build prescribed, 80% of the videos are not specific to a specific drone build. This means you can still extract extremely valuable knowledge from this course without needing to spend the money to buy the drone parts. Even without building a drone, you’ll still learn about the hardware, design and build processes, and some best practices and maintenance for drone pilots.

    What if you want to build a drone, but not the type used in this course?

    This would work just fine, because there is even a section dedicated to illuminating the design process, which would allow you to design and find the parts for your own drone build. Most of the videos would still directly apply to your drone.

    What about required tools to follow along in this course?

    At minimum, you will need:

    A soldering iron and solder (~$20)

    Screwdriver

    Allen wrench set (~$10)

    Raw drone components to build and maintain the drone ($400 to $500 depending on the quality of parts you choose to buy)

    A drill and some drill bits would be helpful (but not required)

    Should you join right now?

    Check out the free lectures first and see if you think this course is right for you.

    We offer a 30 day money back guarantee on this course, so you can always return it if you decide later the course wasn’t for you.

    Who this course is for:

    Raspberry Pi lovers seeking a drone related project
    Engineers/Programmers desiring a drone that’s easy to prototype with
    Tinkerers wanting to build their own open source ardupilot drone from scratch
    Linux enthusiasts wanting a flyable linux box

    Course information :

    BestSeller | h264, yuv420p, 1280×720 |ENGLISH, aac, 44100 Hz, stereo, | 5h 38 mn | 4.43 GB
    Created by: Caleb Bergquist

    Course Link :

    https://www.udemy.com/course/how-to-build-a-drone/

    Key words :

    Course Build a Linux Based Raspberry Pi Drone.

    Udemy Build a Linux Based Raspberry Pi Drone.

    Download Build a Linux Based Raspberry Pi Drone.

    Likk Download :

    SamaUp

    File-Up

    UpToBox

    See More

    With regards CourseDown.Com

    Sorry, we couldn't find any posts. Please try a different search.

    Share on facebook
    Facebook
    Share on twitter
    Twitter
    Share on whatsapp
    WhatsApp
    Share on pinterest
    Pinterest
    Scroll to Top